Evaluation kit that acts as a platform for the NXP MC56F80x digital signal controllers MCU family with form-factor compatibility to Arduino R3 pin layout.

MC56F80000-EVK Evaluation Kit

<p>NXP MC56F80748 has 64 kB on-chip flash memory and 8 kB on-chip RAM. The MC56F80xxx device family is based on a 32-bit 56800EF core with up to 100 MIPS at 100 MHz core frequency. The device coordinates the rotation of the digital computer (CORDIC) engine. The MC56F80000-EVK board has OpenSDA, 3-axis MEMS accelerometer, PWM and user LEDs, buttons, ADC test circuits, OPAMP test circuits, and external serial flash memory. The evaluation kit is a development platform for the MC56F80x digital signal controllers MCU family with form-factor compatibility to Arduino™ R3 pin layout.&nbsp;</p><h2><strong>MC56F80000-EVK Evaluation Kit Features&nbsp;</strong></h2><p>The MC56F80000-EVK evaluation kit is based on MC56F80748 digital signal controller (DSC). MC56F80x Digital Signal Controllers (DSCs) are based on the 100MHz, 56800EF DSP-core that provides math capabilities for advanced power conversion and motor-control applications. These controllers include peripherals such as an 8-channel eFlexPWM with 312ps resolution, a quadrature decoder, dual high-speed 12-bit ADCs, and three analog comparators. The digital signal controller also contains two operational amplifiers that provide a programmable gain of up to x16. The EVTG and inter-module crossbar build an interconnection network between module I/Os and external pins with hardware logic/trigger operation capability to achieve flexible system configuration.&nbsp;</p><p>The evaluation kit integrates an OpenSDA, which provides an onboard debugger and a virtual serial port for rapid prototyping and product development. OpenSDA MCU is a Kinetis K Series K26 family device on MC56F80000-EVK. For connectivity, users can use a 5 V input power supply using an external DC power supply connector, OpenSDA USB micro-AB connector, USB micro-AB connector, and LD1117 LDO for 3.3 V VDD supply. There is also MCU input/output access through Arduino R3 compatible I/O connectors.&nbsp;</p><p>MC56F80000-EVK uses a 3-axis MEMS accelerometer FXLS8974CF sensor for motion sensing. The kit supports both high-performance and low-power operating modes. MC56F80000-EVK has light-emitting diodes to monitor system functions, such as power-on, board faults, reset, etc. There are three user-defined LEDs and six LEDs controlled by 6 PWM channels. The information collected from LEDs can be used for debugging purposes.&nbsp;</p><p>Debugging is possible using an onboard OpenSDA circuit that supports programming and debugging with CodeWarrior. Users get a 14-pin JTAG port to connect with a standalone programmer to create and test various applications. Eclipse IDE is CodeWarrior for MCUs, while MCUXpresso Config Tools is a graphic tool to configure peripherals and provide stationeries within the CodeWarrior Software Development Kit (SDK). Both of these resources act as additional support for users.&nbsp;</p><h2><strong>Applications</strong></h2><p>MC56F80000-EVK evaluation kit is an affordable development board that can be used in a wide range of embedded applications that require precise control and real-time processing capabilities. Potential applications include motor control, power conversion, lighting control, industrial automation, medical devices, and consumer electronics.&nbsp;</p>

MC56F80000-EVKUM Product Brief

MC56F80000-EVKUM Product Details

MC56F80000-EVKUM User Manual

Product

Product Type

Clock

Sensors

Connectivity

Power management

Applications

The NXP MC56F80000-EVK evaluation kit is a development board that integrates MC56F80748 Digital Signal Controller (DSC). This device combines the processing power of a Digital Signal Processor (DSP) and the functionality of a microcontroller (MCU).

Product	Evaluation Kit
Product Type	Development Boards & Kits - Other Processors
Clock	8 - 16	MHz
Sensors	3-axis MEMS accelerometer
Connectivity	USB interface, Virtual serial port, and Arduino R3 compatible I/O connectors
Power management	OpenSDA USB, Virtual serial port USB, External 5V adapter